Buy Low Price From Here Now
8" Professional, Stack Carbide Tipped Dado, With Steel Shims, 4 Carbide Tipped Chippers, Maximum 13/16" Cut Width In 1/16" Increments.
Readmore
Technical Details
- Features Freud's TiCo¿ Hi-Density Carbide with Titanium for long life and a flawless finish- The negative hook angles make flat bottom grooves and virtually splinter-free cuts
- Slot widths from 1/4-inch to 13/16-inch in 1/16-inch increments
- Set includes two outer blades and five two wing chippers ( 4- 1/8" & 1- 1/16" )
- Includes shim set for micro adjustments
See more technical details
By Vince (Maryland, USA)
I recently bought this dado set for a cabinet project. I was very disappointed in the poor quality of the cuts. The sides of the cuts were very smooth and accurate, but the bottoms of the cuts were very uneven - even worse than simply using a 1/8" saw blade to make repeated passes. I'm using this set on a new Ridgid 10" table saw and the fit on the arbor is extremely snug, so a loose arbor fit isn't the problem.
For hidden dados where appearance or flatness isn't critical, this set is fine. But if you need smooth, even bottom cuts, like for tenon shoulders or exposed rabbets, this blade set isn't up to the task... you're better off using a router or tenoning jig.
By E. Logan (Atlanta)
Being new to woodworking, I am very pleased with these blades. It cuts crisp, flat edges. So far I have used it to cut 1/4, 1/2 and 3/4" grooves, half laps and tenons. Worth the money!
By jose gomez (ca)
once you get the right combination of blades, shims and spacer this is a must have for cutting dado grooves works excellent no problems. highly recommend.
By D. Millman
I bought this a year ago, and have just recently been putting it to a lot of use. After having done several projects now, I am not all that happy with it. I bought it based on the Freud name and the price. Does it work, yes. I can't get flat bottom dado's... Every single time, my dado's have grooving from the outer blades. This has been true with the 5 different dado widths I have cut. Bummer.. The holes in the blades are not all the same diameter, this is a minimal difference but some don't even fit on my arbor... Some are a bit loose... This would probably explain the grooves left in my dado's, and why some people have flat dado's and some don't... As far as the setup chart with shims and chippers goes... The width configurations are confusing.. This has led to a lot of time testing out shim and chipper configurations... An example of confusing shim/stack setup is 13/32" and 15/32" have the exact same configuration, with no further explanation... So what is the real measurement of stack A+B+C+D+S1+S2 if two measurements are given? It would have been a lot better to get an actual cut width and ply width designation. It can be figured out, but wastes time. I have the Forrest WWII as my main blade, which has now set my standard for blades... even with it's high cost, it ends up being well worth it in the long run.. I would not recommend this Freud dado setup for a profesional result, and look forward to buying the Forrest dado set. The best solution to this Freud dado stack setup is to take an hour or two and cut all the dado combinations on to one piece of wood. That way you have this stick to test all of your pieces and quickly the proper stack setup for your project. It is cheap though, so if that gets you cutting dado's, get it!
I did find much more correct dado stack setups at the Freud site. The chart I recieved with my purchase did not have the same information, so they must have figured this out and revised it online. I hope this one IS correct. http://www.freudtools.com/images/manuals/Chipper-Chart.pdf
Happy wood working!
By Peter Hansen (New York City)
This is the least expensive 8" carbide stacked dado that I could find. I bought mine at a big-box store about a year ago. It replaced a 6" steel stacked set that I bought a few years back. It was a big step up and, for a while I was satisfied with it despite the not-quite-flat bottom it left.
Last week I needed to rabbet some pine molding. I didn't have a close look at the dado while I installed it on the arbor. Upon starting the cut, the workpiece vibrated violently as it passed into the dado. I stopped and examined the dado and discovered that the outboard blades were missing a total of six teeth. I'm not sure when I lost the them, but the net result is that I'm now looking for a new dado set as I don't feel like investing $40 or $50 to have the teeth replaced.
I've gone back to doing rabbets with a tall fence and my Forrest Woodworker II blade which I just got back from being sharpened by Forrest. I think I'm just going to have to bite the bullet and purchase a Forrest set as my experience with the WWII blade has been extremely satisfying.
Images Product
Buy Freud D208 8-Inch Professional Dado Now
0 comments:
Post a Comment