Hitachi 18109 12-Inch 8 Tooth FTG Diamond Hardi-Saw Blade with 1-Inch Arbor

Buy Cheap Hitachi 18109 12-Inch 8 Tooth FTG Diamond Hardi-Saw Blade with 1-Inch Arbor

Buy Low Price From Here Now
Kerf: .087". Plate: .063". Carbide Grade: Diamond. Ripping, crosscutting and miter of fiber cement board and siding.
Readmore

Technical Details

- Circular saw blade designed for use with most 12-inch miter saws
- Ideal for ripping, crosscutting, and mitering in fiber cement boards and siding
- Self-sharpening, long-lasting polycrystalline diamond tips
- 8-tooth design for precise, dust-reducing cuts
- 12-inch diameter; 1-inch arbor; 5-year limited warranty
See more technical details

 "Hardie Board Siding" 2008-04-15
By R. Jackson (Orlando, Fl)
I highly recommend the Hitachi blade for installing Hardie Board. I installed siding on a 2700 sq foot house and a 24x36 out building and the blade was still working great.



Ray Jackson

Orlando, Fl

 "Cuts cleanly and lasts" 2007-01-19
By Chad Loder (Lomita, CA USA)
These blades are great: clean cuts, not terribly loud, and durable. Used them on a large Hardie siding job and would use them again.

 "Must have for Hardi-Plank siding" 2006-12-16
By R. C. Stevens (Lebanon NJ USA)
Title says it all. Great blades. These things slice through fiber cement siding like a hot knife through butter. VERY low dust too. Long life on blade--I did a three car garage and attached 170 sq ft mudroom on one blade with no real noticeable dulling of blade. If you were siding a whole house or larger addition, you'd probably need two blades though.

 "Cuts cleanly" 2006-09-07
By PK (Midwest)
Not much needs to be said. This one delivers what you want in a saw blade; no noticeable vibration, cuts cleanly (top and bottom faces!), and lasts a long time considering you are essentially cutting cement and paper. Used on a 12" Bosch SCMS.



One other thing, if you are considering following the manufacturer's advice and using a power shears to cut fiber cement instead of a saw blade to minimize dust, save your money, buy a dust mask, and get this blade. The shears won't ever get you consistent edges and smooth cuts like this (I regretably wasted my money on the PC one). Also, use a sharp utility knife blade to do the 'score and snap' method for those cuts the SCMS cannot do -- and get the Malco nippers too!


Images Product

Buy Hitachi 18109 12-Inch 8 Tooth FTG Diamond Hardi-Saw Blade with 1-Inch Arbor Now

Read more “Hitachi 18109 12-Inch 8 Tooth FTG Diamond Hardi-Saw Blade with 1-Inch Arbor”

Skil 94100-05 Pruning Reciprocating Saw Blades, 5-Pack

Buy Cheap Skil 94100-05 Pruning Reciprocating Saw Blades, 5-Pack

Buy Low Price From Here Now
Ulgy reciprocating saw blade for fast cutting in wood, pressure treated lumber, and composition board. 4-5 TPI, 9" length. Available Only At Cape, Mesquite, Woodburn. 5 per card
Readmore

Technical Details

- Reciprocating saw blades for extremely fast cutting in wood, pressure-treated lumber, wet wood and composition board
- Made of high-carbon steel with fire-hardened, precision-ground cutting edge for performance and durability
- Fleam ground design for cutting on both forward and reverse strokes
- Can also be used for pruning
- For use with all Skil and major brand reciprocating saws
See more technical details

 "Skil "pruning" blades..." 2009-06-14
By Rusty (CA)
These blades don't work any better or cut any faster than any reciprocating blades for wood cutting, which is exactly what these are. They are not special pruning blades, as the description suggests. They are much more flexible than my old blade, which I don't consider to be a benefit.

 "Fantastic Blade" 2009-05-15
By Raymond Baginski (Pitcairn, Pa. USA)
These blades are Awesome. Just watch your fingers cause they are real sharp. Great for demo work. I will purchase more.

 "Not too bad" 2008-09-04
By Texaroo (Kerrville TX)
I purchased "Skil 94100-05 Pruning Reciprocating Saw Blades" specifically to use in pruning a flowering pear and a couple live oak trees. Since none of the branches have a diameter greater than 5 inches I thought they would work. Turns out I was right, they were able to walk through the limbs fairly well IF I supplied pressure to the branch to widen the kerf as I cut. The teeth need to be offset from each other to widen the cut as you go. Otherwise, the blade gets really hot, smokes and I would imagine hurts any tempering the blade may have started with. They get the job done, but they could be improved.

 "Great price, perfect for yard work" 2008-08-26
By CM-mnky
This multi pack from Amazon is the same price for (1) blade at my local chain store. These blades work great for everyday yard work.

 "Great for tree pruning " 2008-08-18
By David Nox (Mississippi USA)
I don't like to pull out the gas chainsaw out for small jobs. I bought a 18v reciprocating saw and use these blades. They go through small trees with ease. I have used them on small trees with up to an 6 inch diameter. They rip right through them. No mess no fuss.


Images Product

Buy Skil 94100-05 Pruning Reciprocating Saw Blades, 5-Pack Now

Read more “Skil 94100-05 Pruning Reciprocating Saw Blades, 5-Pack”

MK Diamond 158434 MK-225 Hot Dog 7-Inch Wet Cutting Continuous Rim Diamond Saw Blade with 5/8-Inch Arbor for Porcelain and Vitreous Tile

Buy Cheap MK Diamond 158434 MK-225 Hot Dog 7-Inch Wet Cutting Continuous Rim Diamond Saw Blade with 5/8-Inch Arbor for Porcelain and Vitreous Tile

Buy Low Price From Here Now
Wet cutting premium grade blade with .050" edge thickness for use with all tile saws. Designed for cutting porcelain and vitreous tile.
Readmore

Technical Details

- Premium-grade, thin-rim diamond blade for wet cutting marble, porcelain, vitreous, and ceramic tile
- Innovative tension slots prevent dishing and blade wobble
- Stiffened slot and ultra-thin kerf delivers less drag and resistance
- Not intended for use on metal, plastics, wood, or any other non-masonry materials
- Measures 7-by-0.05-by-5/8-inches (diameter x width x arbor)
See more technical details

 "Hot Dog !!!!!!!" 2009-08-11
By Richard S. Laub III
I've cut alot of tile in my life. Once I purchased this blade my cuts are more accurate, faster cutting and this blade really lasts. I've cut everything with this blade without any hesitation, including granite and travertine.

 "No Nonsense Blade" 2008-02-01
By DIY Dude (Central FL)
Replaced the stock blade with this one. Well worth the purchase. Wish I had gotten this one early in the tile/granite job so I could comment on the durability. However so far so good.

 "is a gooood product" 2007-07-12
By Eleazar M. Hernandez (Lawrenceville,GA)
is a good blade ;it does not last as long as they say but make very fine cuts and fast i am ok with that and this is my 7 i buy some here and some in other stores try it ...........

 "Great tile blade!" 2007-01-04
By T.G. (CT United States)
This blade is worth the money for faster, good quality tile cuts even through porcelain tiles. Amazon's price was about 30% less than the local tile store!


Images Product

Buy MK Diamond 158434 MK-225 Hot Dog 7-Inch Wet Cutting Continuous Rim Diamond Saw Blade with 5/8-Inch Arbor for Porcelain and Vitreous Tile Now

Read more “MK Diamond 158434 MK-225 Hot Dog 7-Inch Wet Cutting Continuous Rim Diamond Saw Blade with 5/8-Inch Arbor for Porcelain and Vitreous Tile”

MK Diamond 159407 MK-99 10-Inch Dry or Wet Cutting Segmented Saw Blade with 5/8-Inch Arbor for Concrete and Brick

Buy Cheap MK Diamond 159407 MK-99 10-Inch Dry or Wet Cutting Segmented Saw Blade with 5/8-Inch Arbor for Concrete and Brick

Buy Low Price From Here Now
* Dry cutting blade fits all popular saws and angle grinder * Cuts most masonry materials, including brick, block, landscape pavers, fiber cement board, concrete, stucco, roof tile, and asphalt * This tough blade will cut 70 times longer than abrasive blades * Segmented rim * 075" blade thickness * 5/8" arbor * 10" blade
Readmore

Technical Details

- Wet/Dry Paver Cutting
- MK-99 10 Inch Segmented Rim
See more technical details

 "MK Diamond 159407 MK-99 Saw Blade" 2009-08-10
By Carl L. Friedrich
Excellant blade for the price, I used it to cut concrete pavers and had no problems. probably cheaper than renting a wet saw, I recomend this blade highly, cut the pavers fast and nice smooth cut, no chips..

 "Concrete Saw Blade" 2009-06-26
By Rolnald L. Hazel (Chicago)
I installed this on my MK wet saw to cut concrete pavers that were 4x8. It cut them like I was cutting wood. Worked great.

 "Great Blade!" 2009-05-12
By ksem (Los Gatos, CA)
This blade lasted for 2-3 weeks in a wet saw while building a stone wall, and cut perfectly well throughout it's life. What more can you ask for in a 10 inch blade that is under $30?

 "Good Blade for the Money" 2008-09-24
By KJN (Novi, Mi.)
Worked well for dry cutting 4" x 8" x 2.6" pavers. I made approx. 40 diagonal cuts to finish a job and the blade was cutting about as well at the end as on the first cuts. It's a good value under 30 bucks.

 "Awsome Blade" 2008-08-26
By William Moore (Cadiz, KY)
I bought 2 of these since they were so cheap compared to some and I had a lot to do. I cut at least 60 3 inch thick by 12 inch concrete wall caps with it some cuts were 45 degree angles so the cut was very long. I finished the job and never opened the second blade. It was still cutting as fast as the first cut. Highly recommend it.


Images Product

Buy MK Diamond 159407 MK-99 10-Inch Dry or Wet Cutting Segmented Saw Blade with 5/8-Inch Arbor for Concrete and Brick Now

Read more “MK Diamond 159407 MK-99 10-Inch Dry or Wet Cutting Segmented Saw Blade with 5/8-Inch Arbor for Concrete and Brick”

Freud SD206 6-Inch Professional Dado

Buy Cheap Freud SD206 6-Inch Professional Dado

Buy Low Price From Here Now
Stack dado set has anti kickback, splinter free cuts, negative hook angle for flat bottom grooves. Can be used on table saws, radial arm saws for cutting slots, grooves, dadoes, and rabbets in plywood, hard, and softwoods. Includes: (2) outside blades, ca
Readmore

Technical Details

- An ideal dado set for smooth, flat-bottomed grooves
- Provides splinter-free cuts
- Anti-kickback design
- 5/8-inch arbor
- Limited lifetime warranty
See more technical details

 "can't believe this has so many 5 star reviews" 2009-09-29
By F. Kirk (Atlanta, GA)
Maybe I shouldn't complain; I got this product on sale. However, everytime I cut a dado I have significant tear out on the back side of the cut and the bottom is ANYTHING but smooth - so I smooth it with a float. Also, the plastic holder broke, but I suppose that is just the way plastic containers are. As the other reviewers mentioned, hang on to your instructions - they are just a small piece of cardboard. If I had it to do all over again, I would read the other product reviews and invest in a higher priced dado set and hope that the bottom of the cut is close to being smooth. There are a lot of folks that like this product, so maybe I just got a lemon.

 "Great Cuts and perfect for smaller saws" 2009-09-13
By Jordan H. Shatsoff (Waltham, MA)
The cuts from this dado set are great. It's perfect for a portable saw like the Ridgid TS2400. The lack of markings on the shims are a minor nuisance, but using them gives excellent results.

 "No problems" 2009-04-04
By Rick A. Gifford (West Virginia, USA)
Ihave used this set for several projects now. The instructions are clear for the settings, and so far I have found them to be very accurate.



I think this is a good set. I would hate to go back to my old set with shims.



I picked this up on sale. Keep an eye on it as the price goes up and down. You can find this on Amazon at a reduced price if your lucky.

 "Good Dado - but Does Not Fit Jet XactaSaw Deluxe!" 2008-07-27
By New England Yankee (Northern New England)
Great dado set - very high quality, flat-bottom dados. It does not fit the Jet Xacta Saw Deluxe tablesaw, however. While the tablesaw's dust shroud does have a semi-circular cutout, it is not big enough to accommodate the dado set's dial. If possible, you should check for fit on any saw with such a shroud before buying.

 "Infinitely adjustable, yet easy to use." 2008-07-21
By J. Dubovsky (Blacksburg, VA USA)
I've used this extensively on my Grizzly 1023 table saw with great results. I would highly recommend this blade set to anyone. My advice on using it:

* when you unbox the blades, measure the chipper thicknesses and label them "A", "B", "C", etc., according to the manual. There one that's thinner than the others, and it is required for certain thickness combinations; identifying it by sight is almost impossible. I wrote on them in silver Sharpie and it solved that problem.

* mark the "zero" on the thickness adjusting dial. Turn it until the back of the dial is perfectly flush with the back of the blade and write a "0" above that tick mark (again, silver Sharpie works great). That way, when the manual says "a 1/2 inch dado is these three blades plus four clicks" you'll know that you're really at four and not, say, three or five.


Images Product

Buy Freud SD206 6-Inch Professional Dado Now

Read more “Freud SD206 6-Inch Professional Dado”

Freud D0640X Diablo 6-Inch 40 Tooth ATB Trim Saw Blade with 1/2-Inch Arbor

Buy Cheap Freud D0640X Diablo 6-Inch 40 Tooth ATB Trim Saw Blade with 1/2-Inch Arbor

Buy Low Price From Here Now
Thin kerf saw blade for cordless saws. Alternate top bevel, .039" plate, .049" kerf, 18 degree hook angle, 2,000 max RPM.
Readmore

Technical Details

- Laser cut stabilizer vents trap noise and vibration keeping it cool and reducing blade warp
- Laser cut heat expansion slots allow blade to expand due to heat build-up keeping the cut true and straight
- Durable micrograin titanium carbide for extreme durability, razor-sharp cuts, and long life
- Tri-metal shock resistant brazing allows carbide tips to withstand extreme impact for maximum durability
- Laser cut arbor for accurate blade rotation reducing vibration and premature wear
See more technical details

 "Excellent Blade" 2009-05-22
By W. Holt (Benton, AR)
I had a tough time finding a 1/2 inch arbor for my old circular saw. I found this one at Amazon and have been very satisfied with its performance. The thin kerf is very helpful on delicate cuts.

 "saw blade" 2008-07-26
By R. Stochl (Wildwood, Il USA)
Good blade for the price. Teflon coating reduces drag and heat build up. You get a nice smooth cut with this blade.

 "Nice blade in a hard-to-find size" 2008-06-11
By Robert Cotton (Orlando FL)
My saw is a Porter Cable Saw Boss. It's a great saw, but the 6-inch blades are hard to find. It's good that Freud sees fit to make them. The cutting ability of my saw was improved with the new blade, even though the blade on the saw already was still very sharp. I like Freud blades, and use them on my table saw, too.


Images Product

Buy Freud D0640X Diablo 6-Inch 40 Tooth ATB Trim Saw Blade with 1/2-Inch Arbor Now

Read more “Freud D0640X Diablo 6-Inch 40 Tooth ATB Trim Saw Blade with 1/2-Inch Arbor”

Milwaukee 49-22-1127 11-Piece Super Sawzall Bi-Metal Blade Set

Buy Cheap Milwaukee 49-22-1127 11-Piece Super Sawzall Bi-Metal Blade Set

Buy Low Price From Here Now
Bi-metal blades feature custom ground teeth, set and hardened for maximum performance with 1/2" universal tang for reciprocating saws Includes one each blade -5031 and -5036 for fast cutting, roughing-in work (6 inch and 9 inch respectively) and -5041 for wood scroll Packaged in a reusable vinyl pouch, this general purpose Sawzall Blade kit includes one each blade -5162 for metal scroll, -5182 for metal cutting 3/16"-1/4", -5184 for metal cutting 1/8"-3/16", -5186 for metal cutting less than 1/8" thick Also includes one each blade -5091 for nail embedded wood & composition material (6 inch), -5092, -5093, -5094 for nail embedded wood & composition material (6 inch, 8 inch and 12 inch respectively)
Readmore

Technical Details

- 1 Assortment
See more technical details

 "Milwaukee Tools the best there is at this price." 2009-09-07
By S. Howes (USA)
I own a large selection of Milwaukee tools and a few Hilti tools. IMO, getting Milwaukee products are like getting Hilti products for a little less money. However, if you work in punishing, demanding conditions everyday, all day, then Hilti may be the way to go for the very long haul. For 90%, Milwaukee is a good bet

 "Super sawzall blades" 2009-04-28
By jeepers
The blades are just what the average person needs, good selection and a lot cheaper than buying them one at a time. Plus you get to find out quickly which ones you use a lot, for future purchases.

 "Great Selection - Great Price" 2006-07-30
By Rick (Mililani, HI)
Really - you'll end up using every blade at one time or another. It's great to have the right blade for the right job. Sure-save a few $$ and buy just a few blades, but then it's a trick to try to guess which blade might do the trick. Get them all, you'll be smiling when you get to change blades and it'll cut through whatever like a hot knife through butter.

 "Good assortment to start" 2005-10-22
By Shawn McMurdo (Santa Cruz CA USA)
This is a good assortment of blades to start with. I have only used a couple of the blades so far but it is nice to have the variety for the odd jobs when I will need them.

The blades I have used for metal and wood cutting have held up well so far.

 "A must have for your saw" 2004-10-29
By Frank Yoerg (Calumet, MI United States)
An excellent addition for your tool box. It is always a good idea to have back-up blades when starting a project, and this packet fits the need perfectly. Very good quality blades, from a well respected name in power tools.


Images Product

Buy Milwaukee 49-22-1127 11-Piece Super Sawzall Bi-Metal Blade Set Now

Read more “Milwaukee 49-22-1127 11-Piece Super Sawzall Bi-Metal Blade Set”

Fein 63502106015 3-1/8-Inch High Speed Steel Segmented Saw Blade

Buy Cheap Fein 63502106015 3-1/8-Inch High Speed Steel Segmented Saw Blade

Buy Low Price From Here Now
High Speed Steel (HSS) blade for fiberglass, carbon fiber, 20 gauge sheet metal, and harder woods. Segment to cut right angles without overcutting. This blade is flat.
Readmore

Technical Details

- High-speed steel blade with segmentation on one side
- Rigid material provides for more durable blade and better cutting ability
- Segmentation allows for cutting into corners and right angles; designed for straight cutting in harder material
- Cuts sheet metal up to 1mm and harder wood, fiberglass and carbon fiber
- Weighs 8 ounces shipped
See more technical details

 "Where is Makita when you need them?" 2009-07-13
By Sudoku Junky (Los Altos, CA USA)
I love using this tool but for 3 things:

Brittle blade - my first one shattered when the tool it was mounted to hit the concrete floor.

Breath taking accessory prices.

The blade lock lever is too stiff for my small hands - it will snap shut breaking fingernails.

 "Fien Multi-master 3-1/8" HSS Segmented Saw Blad" 2009-05-29
By Sube (SoCal)
Great product, if a bit expensive, amazingly versatile for cutting precise notches into corners, holes in cement backer board and clean, straight lines through dry wall, and just about any metal or wood projects you can imagine. These blades hold their saw teeth edge very well. Since they are not a common, off-the-shelf item, it's a good idea to keep a spare available. Fein 63502113019 3-5/16-Inch Flush Cut Wood Blade

 "They are able to be repaired" 2008-12-21
By Larry A. Jones
I found these blades to be somewhat fragile also. I accidently vibrated the center "teeth" out of the blade. I just clamped the blade to a piece of dull brass plate with a 2" slice of pipe to protect the blade teeth. I then filled the entire hole with silver solder, the hard stuff. Keep the heat on the edges of the hole. No flux. The solder wont stick to dull unprepared brass. When it is cool some sanding to flatten the solder plug. put another blade over it and mark the serations and hole. use a small 5/32 drill bit and drill out each one of the seration marks. At this point you can remove the center in many ways, but I recommend grinding with a handheld rotary tool. cut each of the holes in the center. You dont have to be all that accurate about any of this to be successful. it will fit right on and all it takes for time is about 1/2 hour. These blades can be resharpened as well. Breaking this blade can be avoided by being sensitive to how the tool feels while you are cutting. The audible report they issue when being bent or side pressured is very definite, you just need to listen,

 "Beware, this as fragile as a potatoe chip" 2008-08-31
By Robert H. Haberkorn (Sothern California)
I bought this blade to replace the one that came with the kit. When I tried to install it the blade must have been just a little off center. As soon as I put pressure on it, the blade shattered into a dozen pieces. I haven't used the new one yet, I am afraid of breaking it too.

 "OH PLEASE!" 2006-10-29
By M. Cooke
You might think this blade is made of solid gold for the price Fien wants for it, but it's not. If it was solid gold it would be cheaper! Go on E-Bay and search for Fein blades at a reasonable price and don't waste your money here.


Images Product

Buy Fein 63502106015 3-1/8-Inch High Speed Steel Segmented Saw Blade Now

Read more “Fein 63502106015 3-1/8-Inch High Speed Steel Segmented Saw Blade”